What Wear-Resistant Steel Plate Is
A wear-resistant steel plate is a low-alloy steel that is quenched and tempered to a high hardness, giving exceptional resistance to abrasion from sliding, scraping, and impacting materials. Grades such as NM400 and NM500, produced to GB/T 24186, are widely used in dump truck bodies, excavator buckets, chutes, hoppers, crusher liners, and other earthmoving components. The NM designation is followed by a number indicating the nominal Brinell hardness, so NM400 has a hardness in the range of about 360 to 440 HBW and NM500 about 470 to 540 HBW.
NM400 and NM500 Compared
NM400 offers a balanced combination of hardness and toughness, making it suitable for moderately abrasive materials and for parts that also experience impact. NM500 is harder and more abrasion resistant, extending service life in severe sliding-wear applications, but its toughness is lower and its cutting, forming, and welding are more demanding. As a rule, NM400 is the first choice for structural wear components and general-purpose liners, while NM500 is reserved for the highest-abrasion zones where impact is limited, such as hopper sides and chute bottoms handling coarse ore or aggregate.
How 42CrMo and S45C Compare
42CrMo is an alloy steel with about 0.38 to 0.43 percent carbon plus chromium and molybdenum, hardened and tempered for high-strength machine parts such as shafts, gears, and pins; its wear resistance comes from heat treatment rather than from being a dedicated wear plate. S45C is a medium-carbon steel with about 0.43 to 0.50 percent carbon, used for general machine parts and sometimes surface-hardened. For lining and abrasion service, NM-series plates give far higher hardness at a lower cost than machined alloy steel, while 42CrMo and S45C remain the right choice where the part must be machined, threaded, or heat treated to a precise hardness.
Cutting, Forming, and Welding Wear Plates
NM plates are cut by plasma or waterjet; oxy-fuel cutting is possible but leaves a hardened cut edge that should be ground before service. Bending is limited to generous radii, and holes are preferably drilled or waterjet-cut because punching can crack the hard material. Welding uses low-hydrogen consumables such as E7018 or specialized hard-facing wires, with preheat of about 100 to 200 degrees Celsius depending on plate thickness, and the weld schedule must be approved for the hardness grade. Because the hardened structure is damaged by heat, welds should be placed away from the wearing surface wherever possible.
Selecting the Right Grade for the Application
Start from the wearing mechanism: high-speed sliding of hard abrasive material favors NM500 or harder grades, while impact, bending, and welded fabrication favor NM400 or even NM360. Machined and load-bearing components should be specified as 42CrMo or S45C with the required heat treatment. For every application, the plate thickness is set so that the remaining cross-section after wear still carries the structural load, and the liner is usually bolted or welded in replaceable segments to keep maintenance costs low.
Frequently Asked Questions
Q: What hardness does NM400 have?
NM400 is quenched and tempered to a hardness of approximately 360 to 440 HBW, with the nominal value stated in the mill certificate.
Q: Can wear plates be welded to mild steel structures?
Yes, with low-hydrogen consumables and controlled preheat, wear plates are commonly welded onto mild steel hoppers and buckets as replaceable liners.
Q: Why not use 42CrMo as a wear liner?
42CrMo is a high-strength alloy steel for machined parts; using it as a liner is expensive and its service hardness is normally lower than that of NM plates unless it is surface hardened.
Q: What is the difference between NM450 and NM500?
NM500 is harder, with about 470 to 540 HBW against about 420 to 480 HBW for NM450, giving better sliding-wear life but reduced toughness and weldability.
Q: What thickness range is available?
Wear plates are commonly supplied from 3 mm to 100 mm thick, with widths up to 2500 mm, and can be cut to the required liner patterns before delivery.



















