S275JR vs S355JR Structural Steel: Composition and Property Comparison

Oct 29, 2025

Leave a message

Two Strength Levels From the Same Standard

S275JR and S355JR are both non-alloy structural steels supplied under EN 10025-2, the European technical delivery standard for hot-rolled products of structural steels. Because the two grades share the same standard, the same delivery condition and much of the same chemical envelope, they are frequently compared during design. The practical difference is one of strength level: S355JR delivers roughly 30 % more yield strength than S275JR for the same section, so a lighter or thinner member can often carry the same load.

The choice between them is not simply a matter of taking the stronger grade. Higher strength comes with higher carbon and a slightly lower elongation, which changes weld procedures, forming limits and sometimes the cost balance between steel weight and fabrication effort.

Grade Designation Explained

Both designations follow the same logic, so reading one explains the other.

S - structural steel for general construction purposes.

275 or 355 - minimum upper yield strength ReH in MPa for the thinnest thickness range.

J - impact testing is specified.

R - minimum Charpy V-notch impact energy of 27 J.

JR for both grades - the impact test is performed at +20 °C, so neither grade is qualified for low-temperature service; S275J0, S275J2, S355J0 and S355J2 cover lower test temperatures.

Products supplied in these grades include plate, sheet, wide flats, beams, channels, angles and flat bars, which means the grade comparison matters for almost every part of a structural package.

Chemical Composition Comparison

The table below compares the two grades on a ladle analysis basis for material up to 40 mm thick. The trend is consistent: the higher-strength grade is allowed a little more carbon and manganese, while the residual elements that harm toughness and weldability are capped at the same levels.

Element S275JR S355JR
Carbon (C) 0.21 % max 0.24 % max
Manganese (Mn) 1.50 % max 1.60 % max
Phosphorus (P) 0.045 % max 0.045 % max
Sulphur (S) 0.045 % max 0.045 % max
Nitrogen (N) 0.009 % max 0.009 % max
Copper (Cu) 0.55 % max 0.55 % max

The extra carbon and manganese in S355JR raise the carbon equivalent, which is why heavier S355JR sections and highly restrained joints are more likely to require a formal preheat check before welding than the equivalent S275JR component.

Mechanical Properties Comparison

Property S275JR S355JR
Minimum yield strength ReH, up to 16 mm 275 MPa 355 MPa
Minimum yield strength ReH, over 16 to 40 mm 265 MPa 345 MPa
Minimum yield strength ReH, over 40 to 63 mm 255 MPa 335 MPa
Minimum yield strength ReH, over 63 to 80 mm 245 MPa 325 MPa
Tensile strength Rm 410 to 560 MPa 470 to 630 MPa
Minimum elongation A 23 % 22 %
Charpy V-notch energy 27 J at +20 °C 27 J at +20 °C

Both grades lose strength as thickness increases, following the same pattern caused by slower cooling and coarser grain structure in heavier sections. The yield ratio and the elongation figures are similar enough that ductility is rarely the deciding factor; load requirement, deflection limits and connection design normally decide the grade.

Selection, Weldability and Applications

S275JR is the economical choice for light to medium structural work: general building frames, machinery bases, support brackets and secondary members where the imposed loads are moderate. S355JR becomes attractive where higher loads must be carried in a given envelope, where member depth is limited, or where reducing steel weight lowers the total cost of the structure even though the price per tonne is higher.

Deflection rather than yield strength governs many designs, and in those cases moving from S275JR to S355JR brings no benefit because the modulus of elasticity is the same for both. The upgrade pays off when the design is strength-governed, when section depth is constrained, or when a lighter member reduces foundation and transport costs.

Both grades weld readily with manual metal arc, MIG/MAG, TIG and submerged arc processes. Neither has inherent atmospheric corrosion resistance, so painted, galvanized or coated systems are used for outdoor exposure; where weathering behaviour is required, a different grade family has to be selected. Typical applications include building and bridge structures, steel frames, machinery supports, fabricated steel components and general engineering work.

Frequently Asked Questions

Q: What is the main difference between S275JR and S355JR?
The strength level. S275JR has a minimum yield strength of 275 MPa and S355JR a minimum of 355 MPa for the thinnest range. S355JR also permits slightly higher carbon and manganese, which is what supports the higher strength.

Q: Do both grades have the same impact test requirement?
Yes. The JR suffix means 27 J minimum Charpy V-notch energy at +20 °C for both grades. Neither is intended for sub-zero service, which requires the J0 or J2 variants.

Q: Is S355JR harder to weld than S275JR?
It is slightly more demanding because of the higher carbon equivalent, but both are readily weldable. Thick sections, high restraint and cold conditions are the situations where a preheat calculation is most likely to be needed for S355JR.

Q: Can S355JR be substituted for S275JR without approval?
The stronger grade usually satisfies the strength requirement, but substitution still needs engineering sign-off because it changes weld procedures, toughness assumptions and, in some specifications, the permitted carbon equivalent.

Q: Which grade is more cost effective?
It depends on whether the design is strength-governed. If deflection controls the section size, paying for the stronger grade brings no benefit; if strength controls it, S355JR can cut steel weight enough to offset its higher unit price.

Q: Do both grades come in the same product forms?
Yes. Plate, sheet, wide flats, beams, channels, angles and flat bars are available in both grades, so a project can standardise on one grade across a structural package.

Q: What inspection documents apply to these grades?
An inspection document to EN 10204 type 3.1, containing heat analysis and mechanical test results, is the usual requirement for structural work. Where the project demands it, independent third-party inspection of dimensions, chemistry and mechanical properties can be arranged.